Easy way to hem pants-How to Hem Pants like a Pro (Follow 6 Easy Steps)

Captivating is built specifically for bloggers! Buy now. Awkwardly short pants make me cringe. So much so that I can barely look at this photo above. I was cringing the entire time I put on these pants and took the photo.

Easy way to hem pants

Easy way to hem pants

Easy way to hem pants

Easy way to hem pants

Using a seam ot, rip the old hem seam. This is some wonderful information to know. Really interesting stuff …. Press the new hem well. This will really help keep it straight while sewing your hem. Pull the pant leg opening really tight and then fold it upwards. Chemise model Easy way to hem pants tip to help the hem fold nicely at the side seams: Clip into the seam without cutting through the entire seam allowance at the hem line, and halfway to the cut edge. It takes a lot of patience to sew. Always test in an inconspicuous spot first.

Burmuda nude. Reader Interactions

To make sure the hem is nearly invisible from the outside of the pants, pick up only one or two fibers at a time on that side of the fabric. Expert Tip: When you Eash picking up a few threads from the fabric, before pulling the Easy way to hem pants all the way through check the side of your pants that hemm going to show. Allison munn sexy the pants and turn them inside-out. Check yourself out in the mirror. Just like that give it a straight stitch all around and that should do it! Wonderful idea!!! They fit so much better now! Decide on the hemline. Brenda Ackerman September 10, Email Address. Stop stitching 1 inch before the same place where you started.

You may have a pair of pants that look great on the booty but are too long or short for your legs.

  • Lots of free sewing patterns and tutorials for making bags, zipper pouches, quilts, mini-quilts, easy clothing items, and other crafty little things to sew.
  • Next time you find a pair of pants that are perfect in every way except their length, go ahead and buy them!
  • September is National Sewing Month!
  • Jun 2, 16 comments.

You may have a pair of pants that look great on the booty but are too long or short for your legs. Use this tutorial to help you learn how to hem your own pants.

You will need to remove the stitching that is already there. A seam ripper works so much better and quicker than a pair of scissors. Be careful not to cut or poke the fabric itself. Along the very edge of the hem, you may see a zigzagged or looped stitch. This is in place to keep the end of the fabric from unraveling.

Leave this stitching intact if possible. Plug in your iron and let it heat up. Some fabrics are not heat-safe, and will actually melt when an iron is applied, so test a small area first. This step is a great way to test your pants to see if they can be ironed in the future. Checking the tag can sometimes give you this information. When in doubt, lay a damp towel between your iron and the fabric. Repeat with the other leg. Put on the pants you want to hem. Wear the pair of shoes that you plan on wearing with the pants.

Hemming pants without the shoes on will make the hem too short! On the side of your left leg, fold the hem up and inside the pants. Use a full-length mirror to get the best idea of what the end result will look like. Adjust as needed until it looks right in the mirror. Pin the hem in place at the top and bottom. Insert one pin first along the top of your hem.

Make sure the fabric is straight before you insert your second pin at the bottom. You do not need to do this to both legs. Take another look in the mirror to see if it still looks right. Take off the pants. Carefully turn them inside out without disturbing your pins.

With your measuring tape, find the length from the bottom fold to the top edge of the fabric that you folded up and inside the leg. Use this measurement to fold and pin the rest of the hem.

Measure in at least in four places all the way around to make sure it is even. Use chalk to mark each measurement. Do not use a pen, pencil or markers, because they can stain and even run after washing. Measuring correctly now means less to adjust later. Measure, fold and pin the other leg in the same manner. Ironing will put your new hem in place. You will be creating a new crease along the bottom and erasing the old one as though it were never there! Ironing may seem like a trivial step, but it is the foundation of hemming.

Iron all the way around the bottom edge, removing your pins as you go. If you are worried about making mistakes, this would be another good time to try the pants on again and take a second look in the mirror.

The hem can always be re-measured and ironed again before you sew. Replace your pins to hold everything steady while you sew. You should have selected a color of thread that matches or comes close to the original thread used on the pants. It is a good idea to use a piece of thread that is about 3 feet in length. Thread a medium-sized needle. Do not sew around the bottom of the hem.

Load your bobbin and top spool with the same color of thread. The thread should come close or match the original thread used on the pants. Set your machine for a small to medium straight stitch. Be sure to tie off all thread ends on the inside of the pants.

For a quick and easy hem, you can always try the no-sew method using fusion tape. Fusion tape is a fusible material that has an adhesive coating which will bond the fabric together without sewing. It is kind of like double-stick tape but activated with heat.

Fusible tape will come pre-cut in strips and ready to apply to a project like a hem. In fact, it is also known as 'hem tape'. Follow all directions that come with your fusible material as the application may vary. It is a good idea to try a little bit at a time to test what kind of pressure and heat you need to apply with the iron for the best bond. Measure a piece of fusible tape that will fit all around inside the hem. Tuck it inside and iron it according to the instructions on the fusible tape package.

What You'll Need. Gather these supplies and get ready to prepare your pants:. Prepare Your Pants. Unfold the hem completely so that it hangs loose. When your ironing is complete, we can see how long you want your hem. Find Your Length. Measure and Pin. Continue to 5 of 7 below. Iron the Hem. Sewing It Up. Optional No-Sew Method. Read More.

Most pants are factory made practically identical in length so one measurement works great for both pant legs. Louann Kristy on June 10, at pm. Here's a tip to help the hem fold nicely at the side seams: Clip into the seam without cutting through the entire seam allowance at the hem line, and halfway to the cut edge. How to correctly press was an AHA for me. I hope this makes sense. These are all pretty basic and something I do regularly. I like the tip from one of your shows about putting elastic into pants when the waist is loose.

Easy way to hem pants

Easy way to hem pants. 2. Press the new pants hem.

.

3 Ways to Hem a Pair of Pants - wikiHow

Captivating is built specifically for bloggers! Buy now. Awkwardly short pants make me cringe. So much so that I can barely look at this photo above. I was cringing the entire time I put on these pants and took the photo. Now decide how much of that extra hem you want to use to lengthen your pants. Just decide how much you want to take in! Put your iron on a low heat setting and press the area with the tape to bind the fabric together.

You typically need to only iron for seconds, but check the instructions on your fabric tape. Flip the pant leg over and repeat with your 2nd strip of fabric tape. Then repeat for the other pant leg. Unfold your pants and iron again to remove any additional creases. I usually opt for getting the tall size because the rise will usually fit better too and hemming them up a little. I think this strategy could work for that situation as well.

Recipe Rating. Shop my FAVS! Leave a Reply Cancel reply Your email address will not be published.

Easy way to hem pants

Easy way to hem pants

Easy way to hem pants